ASME PALD-2005 Safety Standard for Portable Automotive Lifting Devices
|
ID： |
3563C70BB18940E2BEE5C36E32915249 |
|
文件大小(MB)： |
3.14 |
|
页数： |
78 |
|
文件格式： |
|
|
日期： |
2024-6-23 |
|
购买： |
文本摘录（文本识别可能有误，但文件阅览显示及打印正常，pdf文件可进行文字搜索定位）：
Safety Standard,for Portable,Automotive,Lifting Devices,AN AMERICAN NATIONAL STANDARD,隱籌躋舞鯉常養義薯"翳,ASME PALD-2005,(Revision of ASME PALD-2003),Safety Standard,for Portable,Automotive,Lifting Devices,AN AMERICAN NATIONAL STANDARD,' ■ --- ■ The American Society of,Mechanical Engineers Three Park Avenue * New York, NY 10016,Date of Issuance： May 31, 2006,The next edition of this Standard is scheduled for publication In 2008. There will be no addenda,issued to this Edition-,ASME issues written replies to inquiries concerning interpretations of technical aspects of this,Standard, Interpretations are published on the ASME website under the Committee Pages at http：//,www.asme.org/codes/ as they are issued, and are also published within this edition of the Standard.,ASME is the registered trademark of The American Society of Mechanical Engineers,This code or standard was developed under procedures accredited as meeting the criteria for American National,Standards, The Standards Committee that approved the code or standard was balanced to assure that individuals from,competent and concerned interests have had an opportunity to participate. The proposed code or standard was made,available for public review and comment that provides an opportunity fbr additional public input From industry, academia,regulatoiy agencies, and the public-at-large.,ASME does not “approve,“ "rate,M or *'endorseH any item, construction, proprietary device, or activity.,ASME does not take any positron with respect to the validity of any patent rights asserted in connection with any,items mentioned in this document, and does not undertake to insure anyone utilizing a standard against liability for,infringement of any applicable letters patent, nor assume any such liability. Users of a code or standard are expressly,advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, is,entirely their own responsibility.,Participation by federal agency representative(s) or personfs) affiliated with industry is not to be interpreted as,government or industry endorsement of this code or standard.,ASME accepts responsibility for only those interpretations of this document issued in accordance with the established,ASME procedures and policies, which precludes the issuance of interpretations by individuals.,Nd part of this document may be reproduced in any form,in an electronic retrieval system or otherwise,without the prior written permission of the publisher.,The American Society of Mechanical Engineers,Three Park Avenue, New York^ NY 10016-5990,.Copyright . 2006 by,THE AMERICAN SOCIETY OF MECHANICAL ENGINEERS,闻I rights reserved,Printed in U.S.A.,CONTENTS,Foreword.. * *. 丒丒丒丒。?1,。。。?0.. v,Committee Roster . vi,Preface.. 0.一..….………….. vii,Summary of Changes . ix,Introduction .. . 1,General Requirements .. . . .. .…….………… 3,Part 1 Hydraulic Hand Jacks .. .. 5,Part 2 Transmission Jacks . 8,Part 3 Engine Stands . 12,Part 4 Vehicle Support Stands . ………… 15,Part 5 Emergency Tire Changing Jacks ..…….….………….…..… 19,Part 6 Upright Type Mobile Lifts . .……….… 24,Part 1 Service Jacks . 26,Part 8 Wheel Dollies . ー。………0 31,Part 9 Shop Cranes 34,Part 10 Swing Type Mobile Lifts……….。………37,Part 11 Scissors Type Mobile Lifts . 39,Part 12 Auxiliary Stands. 一……. 41,Part 13 Automotive Ramps. 43,Part 14 High Reach Supplementary Stands . 47,Part 15 Fork Lift Jacks 。ー….…. 50,Part 16 High Reach Fixed Stands. 52,Part 17 Vehicle Transport Lifts 56,Part 18 Attechments, Adapters, and Accessories . 60,Figures,1-1 Typical Single-Stage Hydraulic Hand Jack .. 5,1-2 - Typical Wheeled Pneumatic/Hydraulic Hand Jack.. .. 6,1-3 Typical Pneumatic/Hydraulic Hand Jack .. 6,1-4 Typical Multiple-Stage Hydraulic Hand Jack.. 7,2-1 Typical Hydraulic Transmission Jack. 9,2-2 Typical Pneumatic/Hydraulic Transmission Jacks . 10,3-1 Typical "T"6tyle Single Post Engine Stand . 12,3-2 Typical "H"-Styl它 Single Post Engine Stand.. 13,3-3 Typical Twin Post Engine Stand . 13,4-1 Typical Vehicle Support Stands 15,4-2 Horizontal Dimensions and Vertical Heights for Stability Considerations .. 17,4-3 Application of Load for Off-Center Load Test 18,4-4 Application of Load for Centered Load Test . “ 18,iii,5-1 Typical Screw Jack 19,5-2 Typical Bumper Jack .. 20,5-3 Typical Scissors Jack 20,5-4 Typical Frame Jack.. 21,6-1 Typical Upright-Type Mobile Lift . 24,7-1 Typical Hydraulic Service Jacks 27,7-2 Typical Pneumatic/Hydraulic Service Jacks . .. 28,7-3 Saddle Periphery Limits 一.，. …….….。…………. 29,7-4 Saddle Periphery Test…………………….. 29,8-1 Typical'Wheel Dollies.. ーー………………………. 32,9-1 Typical Shop Cranes 35,10-1 Typical Sw……
……